T5 hook up installation

t5 hook up installation

How do you install a T5 over drive gear?

Installing a T5 might require doing some or all of the following. Make sure your T5 will bolt up to the bell you have. Make sure your T5 over drive gear is a good match for your rear differential. Shorten the drive shaft. Install new drive shaft u-joints and a new slip yoke.

Will a T5 work well with my Chevy engine and bell housing?

Will a T5 work well with your Chevy engine and bell housing? Yes, probably. Heres a list of things to think about. Good planning can help avoid disappointment. The Basics - Heres what you need for an older Chevy car or truck.

Can You bolt a T5 input shaft to a bell?

If you have a good condition 1993 or earlier S10 T5 (Muncie pattern case), then you can make it bolt directly to the bell if you remove the S10 input shaft and install a Jeep T5 input shaft. Doing the Jeep swap will allow you to keep using a 10 spline clutch disc. DIY Jeep input shaft swap instructions LINK HERE.

How do you change a T5 to a V6 Camaro?

Make sure your T5 will bolt up to the bell you have. Make sure your T5 over drive gear is a good match for your rear differential. Shorten the drive shaft. Install new drive shaft u-joints and a new slip yoke. Swap the T5 input shaft (optional for a V6 Camaro T5 and NOT required for a V8 Camaro T5).

How do you fix a Camaro T5 over drive gear?

Make sure your T5 over drive gear is a good match for your rear differential. Shorten the drive shaft. Install new drive shaft u-joints and a new slip yoke. Swap the T5 input shaft (optional for a V6 Camaro T5 and NOT required for a V8 Camaro T5). Buy and install an adapter plate instead of swapping the input shaft.

Why is my T5 overdrive gear not working properly?

You will experience poor performance if the T5 overdrive gear is not properly matched to the rear differential gear in your vehicle. Here are charts showing what I recommend. 5. You will need a 27 spline slip yoke for your drive shaft. PROSHAFT LLC sells new yokes like the Turbo 350 slip yoke that uses the 1310 u-joints. 6.

What is the drive gear on a T5 speedometer?

A T5 with a cable style speedometer output has a plastic gear on the output shaft called the DRIVE GEAR. The DRIVE GEAR turns a smaller gear called the DRIVEN GEAR which turns the speedometer cable. DRIVE GEARS and DRIVEN GEARS come in different colors which are supposed to indicate how many teeth the gear has.

How do you change a T5 to a V6 Camaro?

Make sure your T5 will bolt up to the bell you have. Make sure your T5 over drive gear is a good match for your rear differential. Shorten the drive shaft. Install new drive shaft u-joints and a new slip yoke. Swap the T5 input shaft (optional for a V6 Camaro T5 and NOT required for a V8 Camaro T5).

What is the difference between a Camaro T5 and V8 Camaro?

The V8 Camaro received the same bolt pattern as earlier four speeds but with a 22 degree rotation to place the shifter closer to the driver. It is believed that GM changed the bolt pattern of the V6 T5 so that it couldn’t be installed behind V8 motors. From looking at the outside of a Camaro T5 it is difficult to tell them apart.

Why did GM change the bolt pattern on the T5 Camaro?

It is believed that GM changed the bolt pattern of the V6 T5 so that it couldn’t be installed behind V8 motors. From looking at the outside of a Camaro T5 it is difficult to tell them apart.

Can I swap a V8 Camaro T5 for a Firebird T5?

- No adapter plate is needed. - The Jeep shaft swap is NOT an option for the V8 Camaro/Firebird T5. - The V8 T5 will require a 26 spline clutch disc. - A V8 T5 with a 0.63 OD gear is not a good choice for a low HP engine. - A V8 T5 with a 0.73 OD gear is more suitable for low HP applications.

How do you change the input shaft on a Camaro T5?

Swap the T5 input shaft (optional for a V6 Camaro T5 and NOT required for a V8 Camaro T5). Buy and install an adapter plate instead of swapping the input shaft. Shorten the length of the bearing retainer sleeve. Buy a new clutch disc (required if you install a T5 with either a 14 spline or 26 spline input shaft).

Related posts: